VISIT WEBSITE >>>>> http://gg.gg/y83ws?9147608 <<<<<<
Make a reference mark on the tape on the spot where you want to drill the hole. This will help guide you as you get ready to drill. Part 3. Start drilling at a very slow rpm. You want to drill slower when you are drilling into hard materials; you can find charts online that provide recommended drill speed for different materials, including glass.
Make sure it is secured tightly. You only want to create a dimple in the glass at first. Then, remove the cardboard or tape and drill faster, at about rpm. If you drill too fast, your drill bit could cause burn marks around the tip. If it seems necessary, swap in a larger bit to enlarge your initial hole. The first hole is a "pilot" hole. It will guide the subsequent larger bits as you work your way up to the size of your finished hole [7] X Research source.
Lighten up the drilling pressure and speed even more so when the drill tip is close to breaking through the glass. When drilling glass, you should keep the drill at low or medium speeds. When you are close to breaking through, slow it down even more because this is when the glass can be the most fragile. If you press too hard on the glass with the drill, you could crack it.
Hold the drill perpendicular to the glass so that you prevent chipping. You'll want to use lighter pressure if you're new to drilling to make it less likely you make a big mistake.
Use coolant so the drill bit doesn't get too hot. This is very important. Pour a little oil or water on the area that you are drilling. Water is the most common coolant used on drill bits. You will need to use more coolant if you are drilling a harder surface.
The coolant will keep the drill bit or saw and glass lubricated and cool. If the glass gets too hot while drilling, it can crack and break.
Coolant should be applied both before and during drilling. You could put a bottle with water in it and a small hole in it at the drill hole. It will trickle out and onto the hole as you drill the glass, cooling it. Again, remember to be very careful of electrical cords and water.
Try putting the water in a squirt bottle and apply it as you drill. If white powder forms as you drill, you should apply more coolant, and slow the process down. You could also place a wet sponge under the glass as you drill to act as a coolant.
Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow. Jason Phillip Handyman. Jason Phillip. Support wikiHow by unlocking this expert answer. Not Helpful 0 Helpful 1.
Can I use a titanium drill bit for drilling a small hole in a glass from a picture frame? Mark Spelman Construction Professional. Mark Spelman. Not Helpful 5 Helpful I want to drill a hole in glass, but I'm not quite sure what type of glass it is. How do I tell if it is tempered glass or safety glass? Not Helpful 20 Helpful Not Helpful 0 Helpful 2. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube.
It is extremely important to always wear some type of ventilation mask. The dust caused from drilling glass, known as silica dust, can cause a certain type of lung cancer known as silicosis. Helpful 3 Not Helpful 0. Use a sequence of bits beginning with very small ones and working your way up gradually in size to minimize pressure on the glass.
Helpful 1 Not Helpful 0. Do not overspeed your drill bit. Glass is very hard and abrasive, and bits can be quickly ruined. Helpful 0 Not Helpful 0. Be aware that the drill will probably create chips around the hole edges on the other side but will create a cleaner hole on the side that the drill bit first enters.
Keep the glass cool while drilling. This will avoid breaking tools and glass. This will also help to keep the drill bit and your glass cool. Overheating can cause the diamonds to dull or come off the drill bit and the glass to crack. The piece of sea glass in the above video was 4mm in thickness and took under 50 seconds to drill using a 1.
Some sea glass will take longer to drill through but speeding up the drill or applying more pressure will shorten the life of your drill bit by dulling or burning the diamond grit off. You will make a hole eventually, so patience is the key! Note: If you are using the method whereby you flip the sea glass over and begin drilling again from the other side, do so once you've drilled about half way through and follow steps 1 to 3 again. Once you have mastered the skill of drilling a hole through a pebble or sea glass you can begin to get creative and start to carve and engrave designs into them such as a heart.
I love to use sea glass in it's natural form with all it's irregularities. However, I often have a piece that I just wish I could slice off the top, or remove a little bit. This can be useful when you want it to fit into a setting for instance. With the help of diamond wire hand saw blades you can do this.
Using a small diamond ball burr you can carve a 'dip' into your sea glass so that you can inlay a small gemstone or crystal. A carbide hart bearing cutter is useful if you are using Swarovski crystals.
If you've drilled your hole and then discover it is not wide enough, don't despair, you can always expand the hole size by using a diamond twist drill. These twist drills have diamond grit that is bonded vertically up the shank of the drill bit so they're perfect for expanding hole sizes that have already been created, the flutes grind away at the insides of the hole to make the walls of your hole wider. Helpful note: Do not use a diamond twist drill to make a hole, they are not manufactured for this purpose.
Only use these for expanding an existing hole. We hope you enjoyed this tutorial, and hope it inspires you to get creative and to start drilling sea glass! We would love to see any finished pictures of projects you've embarked on, please send them into us.
How to Find Sea Glass. Home Your Basket Account Wishlist. I tend to mostly use 1mm, 1. The sizes from 4mm and up require the use of a standard house hold drill check the technical tab on the page here for shank sizes If you're at the experimental stage why not try a Diamond Drill Bits Set for your Dremel ,. Step 1. Setting Up 1. Optional: you can hold the sea glass in place with a bit of Blu Tack 3. Safety Before we start, lets make sure our working area is clear, and free of any clutter.
Wear an apron, long sleeves or short sleeves, but no floaty sleeves! That increases your chance of breaking it dramatically. Do not rush the process.
That increases your chances of shattering the glass, and that can cause serious injuries. It also wastes all of the money you spent on the glass.
Lubricate the glass: Drilling holes creates friction and heat. You can simply spray some water on your glass to keep it from getting too dry, but I like to use sewing machine oil or Bones Speed Cream. Both of those are very thin forms of grease, and they reduce friction extremely well. I hope this guide gave you the info you need for your project! I recommend checking out our other tutorials to help you with other crafting projects. Search for: Search. Search Search for: Search.
Comments